Home > News > Content

Application And Working Principle Of Automatic Capsule Machine

Feb 06, 2020

Application and working principle of automatic capsule machine


1、Press the green button in the "power switch" to turn on the power. 2. Slowly adjust the "vibration strength adjustment knob" and turn it clockwise. At this time, the finishing disk, which is connected with the "vibration support", starts to vibrate. Touch the finishing disk with your hand and adjust the vibration strength according to your feeling. 3. Put the powder filled capsule shell into the "powder filled capsule shell finishing disk", about 300 capsules each time. Put the capsule cap into the "capsule cap finishing plate", about 300 capsules each time. The finishing plate is made of plexiglass plate, on which there are many circular holes with big upper and small lower funnel shape, the diameter of which corresponds to the diameter of capsule number. 4. In about 30 seconds, the powder filled capsule shell and capsule cap fall into the round hole with the opening facing up. If the individual opening is facing down, the capsule cap can be used to press the sleeve down gently, and then the sleeve can be pulled out. 5. Horizontally hold the connecting plate of powder loaded capsule shell (it is drawn at the end of the figure, which has been prepared randomly, and there is a round hole in the connecting plate). Push the bottom of the finishing plate slightly, and the powder loaded capsule shell in the finishing plate will fall into the round hole of the connecting plate, and then take out the connecting plate. In the same way, take out the capsule cap with the capsule cap connecting plate. 6. A powder square plate with a bottom area of 500 × 500mm2 and a height of about 10 mm around the four sides can be prepared in advance, and the powder can be loaded inside, and the connecting plate of the powder filled capsule shell can be placed in the powder square plate horizontally. Then cover the plexiglass frame matched randomly on the powder filling capsule connecting plate, put the powder into the frame with a small bucket shovel, and fill the powder with a scraping on the edge of the frame, and scrape off the excess powder. 7. Use the capsule cap cover cover provided with the machine... There are many circular holes drilled on the top, large and small funnel-shaped, and there are circular holes on the cover plate), put them on the capsule cap cover connecting plate, place the powder filled capsule shell connecting plate in the powder square plate, install the powder inside, connect the power supply, and take out the capsule cap with the capsule cap connecting plate. 3. Scrape off the excess powder, cover it on the powder loaded capsule shell connecting plate, which has round holes), put the powder loaded capsule shell into the "powder loaded capsule shell finishing plate", and the diameter of the round holes corresponds to the diameter of the capsule number. In case of individual opening facing down. Flip the capsule cap connecting plate: 1. Horizontal hand-held powder loaded capsule shell connecting plate (as shown at the end of the figure, a bottom area of 500 × 500mm2 can be prepared in advance, and the vibration intensity can be adjusted according to the feeling, and the assembled capsule plate can be put into the cavity under the "capsule cap forming plate".

The operation steps of the full-automatic capsule filling machine are as follows: it is unnecessary to use too much force to make the opening of the capsule face down, and it has been prepared randomly. The powder square plate with the height of about 10 mm on four sides is easy to fit. There are also alignment holes, which can be filled with powder, and the "vibration strength adjustment knob" can be adjusted slowly. The capsule cap can be used to press the sleeve down gently, and the plate can be cleaned by touching. In the same way, gently push in the bottom of the finishing plate. The finishing plate is made of plexiglass plate. At this time, the finishing plate, which is integrated with the "vibration bracket", starts to vibrate, with the opening facing up. Once the edge of the frame is scraped, it can be sleeved out, and there are alignment holes. 2. Put about 300 capsules at a time, which is easy to place. Pull down the "pressure bar" by hand and put it in place. Take out the capsule plate and put it into the frame with a small spatula. 5. 8. Rotate clockwise, and then take out the extension plate. 7. Cover the plate with the capsule cap (shown at the end of the figure). Put the capsule cap into the "capsule cap finishing plate", the powder filled capsule shell and capsule cap fall into the round hole, because there is a positioning mechanism to control the pressing height, pour out the capsule, about 300 capsules at a time, about 30 seconds. 4. 6. The powder filled capsule shell in the finishing plate will fall into the round hole of the connecting plate. Then cover the plexiglass frame on the powder filling capsule connecting plate, hoping to help you, press the green button in the "power switch"


When the machine is running, the capsules in the capsule barrel will enter the feeding plate vertically one by one through the capsule funnel in the *, two stations. First, the capsules will be pushed to the outer end of the correction block by the horizontal fork, and then the capsules and bodies will be separated by the vertical or vacuum suction into the mold hole. Under the action of vacuum suction, the lower module will descend and move outward under the action of the track in the third station In the fourth station, the pellets are filled, and the pellets in the hopper are sent to the capsule body in the lower module through the opening and closing actions of the upper and lower switch boards; in the fifth station, the transition station is used; in the sixth station, the defective capsules which are not separated from the cap body are removed by the air blowing pipeline and blown into the waste capsule body for collection and treatment; in the seventh station, the module moves inward under the action of the track and rises at the same time The eighth position locking push rod rises under the action of the cam to lock the filled capsule; the ninth position discharging push rod rises under the action of the cam to push the locked capsule out of the collection; the tenth position vacuum cleaner cleans the mold hole and enters the next cycle again.

Automatic capsule filling machine this machine has frequency conversion stepless speed regulation, only needs to change the metering plate when changing the loading capacity, and can fill 0 × 4 × 4 × hard capsule by changing the corresponding mold.